نمایش نتایج جستجو برای
موضوع : مهندسی متالورژی و مواد
اعتبار علمی: ISI
موارد یافت شده: 268
1 - Mechanochemical Reduction of MoS2 by Zn in Presence of Lime to Produce Nano-CaMoO4 and -ZnS Simultaneously (چکیده)2 - Physically Based Model of the Yield Strength for an Al-Mg-Si-Cu-Zn Alloy (چکیده)
3 - Thermal stability and non-isothermal crystallization kinetics of Ti41.5Cu42.5Ni7.5Zr2.5Hf5Si1 bulk metallic glass (چکیده)
4 - The effect of Al2O3-nanoparticles as the reinforcement additive on the hot deformation behavior of 7075 aluminum alloy (چکیده)
5 - Microstructural Characterization of Quenched AISI D2 Tool Steel Using Magnetic/Electromagnetic Nondestructive Techniques (چکیده)
6 - An investigation on the energy absorption of aluminum foam core sandwich panel via quasi-static perforation test (چکیده)
7 - FE modelling of the compressive behavior of porous copper-matrix nanocomposites (چکیده)
8 - Evaluation of corrosion resistance of polypyrrole/functionalized multi-walled carbon nanotubes composite coatings on 60Cu–40Zn brass alloy (چکیده)
9 - The Response Surface Method as an Experimental Design Technique to Explore and Model the Performance of Corrosion Inhibitors (چکیده)
10 - Microstructure and mechanical properties of an Al–Mg–Si tube processed by severe plastic deformation and subsequent annealing (چکیده)
11 - Electrochemical and quantum chemical study of Thiazolo-pyrimidine derivatives as corrosion inhibitors on mild steel in 1 M H2SO4 (چکیده)
12 - Microstructural characteristics and mechanical properties of Al-2024 alloy processed via a rheocasting route (چکیده)
13 - In-situ synthesis of nanostructured NiAl-Al2O3 composite coatings on cast iron substrates by spark plasma sintering of mechanically activated powders (چکیده)
14 - Damage mechanisms in aluminum-matrix composites reinforced with nano-alumina particles (چکیده)
15 - Effect of powder reactivity on fabrication and properties of NiAl/Al2O3composite coated on cast iron using spark plasma sintering (چکیده)
16 - Investigation of the effect of solution annealing temperature on critical pitting temperature of 2205 duplex stainless steel by measuring pit solution chemistry (چکیده)
17 - An investigation into the applicability of Barkhausen noise technique in evaluation of machining properties of high carbon steel parts with different degrees of spheroidization (چکیده)
18 - A statistical study on the effect of annealing temperature on pitting corrosion resistance of 2205 duplex stainless steel (چکیده)
19 - The effect of dichromate ion on the pitting corrosion of AISI 316 stainless steel Part II: Pit initiation and transition to stability (چکیده)
20 - Fast Prepared Ni-Al2O3 Nanocomposi te Thro ugh Solution Combustion Synthesis (چکیده)
21 - Effect of grain size on pitting corrosion of 304L austenitic stainless steel (چکیده)
22 - Effect of aging treatment on the crushing behavior of aluminum 6061 alloy tube (چکیده)
23 - A Numerical Approach to the Prediction of Hardness at Different Points of a Heat-Treated Steel (چکیده)
24 - Water-base acrylic terpolymer as a corrosion inhibitor for SAE1018 in simulated sour petroleum solution in stagnant and hydrodynamic conditions (چکیده)
25 - The role of constituent phases on corrosion initiation of NiAl bronze in acidic media studied by SEM–EDS, AFM and SKPFM (چکیده)
26 - The effect of grid configurations on potential and current densitydistributions in positive plate of lead–acid battery vianumerical modeling (چکیده)
27 - Microstructure and corrosion behaviour of plain carbon steel–B4C composite produced by GTAW method in 3?5 wt-%NaCl solution (چکیده)
28 - The effect of homogenization on microstructure and hot ductility behaviour of AZ91 magnesium alloy (چکیده)
29 - Probing of local dissolution of Al-alloys in chloride solutions by AFM and SECM (چکیده)
30 - Effect of thermomechanical parameters on dynamically recrystallized grain size of AZ91 magnesium alloy (چکیده)
31 - Developing an AFM-Based SECM System; Instrumental Setup, SECM Simulation, Characterization, and Calibration (چکیده)
32 - Corrosion Inhibitive Evaluation of an Environmentally Friendly Water-Base Acrylic Terpolymer on Mild Steel in Hydrochloric Acid Media (چکیده)
33 - An insight into the influence of morphological and compositional heterogeneity of an individual intermetallic particle on aluminium alloy corrosion initiation (چکیده)
34 - A comparative H2S corrosion study of 304L and 316L stainless steels in acidic media (چکیده)
35 - Multianalytical and in situ studies of localized corrosion of EN AW-3003 alloy - Influence of intermetallic particles (چکیده)
36 - The Role of Intermetallic Particles in Localized Corrosion of an Aluminum Alloy Studied by SKPFM and Integrated AFM/SECM (چکیده)
37 - Integrated AFM and SECM for in situ studies of localized corrosion of Al alloys (چکیده)
38 - Assessment of Retained Austenite in AISI D2 Tool Steel Using Magnetic Hysteresis and Barkhausen Noise Parameters (چکیده)
39 - Theoretical and experimental investigations on corrosion control of65Cu–35Zn brass in nitric acid by two thiophenol derivativesM (چکیده)
40 - Electromagnetic nondestructive evaluation of tempering processin AISI D2 tool steel (چکیده)
41 - A mechanistic study on the production of nanosized Mo in microwave assisted combustive reduction of MoO3 by Zn (چکیده)
42 - The effect of dichromate ion on the pitting corrosion of AISI 316 stainless steel. Part I: Critical pitting temperature (چکیده)
43 - Correlation between sensitisation and pitting corrosion of AISI 403 martensitic stainless steel (چکیده)
44 - Effect of Thiosulfate on Pitting Corrosion of 316SS II. Metastable Pitting and Transition to Stability (چکیده)
45 - Synthesis of mullite–MoSi2 nano-composite through a mechanochemical processing (چکیده)
46 - Effect of heat absorbing alumina addition on mechanochemical synthesis of WC–Al2O3 nanocomposites (چکیده)
47 - Design of an expert system based on neuro-fuzzy inference analyzer for on-line microstructural characterization using magnetic NDT method (چکیده)
48 - Process Control Strategies for Dual-Phase Steel Manufacturing Using ANN and ANFIS (چکیده)
49 - Incorporation of new technique for processing of Al/SiCp composites based on Evaporative Pattern Casting (EPC) method (چکیده)
50 - Effect of partition coefficient on microsegregation during solidification of aluminium alloys (چکیده)
51 - Effect of Thiosulfate on Pitting Corrosion of 316SS I. Critical Pitting Temperature and Pit Chemistry (چکیده)
52 - Microstructural aspects of in-situ TiB reinforced Ti6Al4V composite processed by spark plasma sintering (چکیده)
53 - Microstructural evolution of aluminum 6061 alloy through tube channel pressing (چکیده)
54 - On the natural aging behavior of Aluminum 6061 alloy after severe plastic deformation (چکیده)
55 - Severe plastic deformation of 6061 aluminum alloy tube with pre and post heat treatments (چکیده)
56 - Deformation Behavior of 6061 Aluminum Alloy Through Tube Channel Pressing: Severe Plastic Deformation (چکیده)
57 - NONDESTRUCTIVE EVALUATION OF MECHANICAL PROPERTIES OF DUCTILE CAST IRON PARTS USING EDDY CURRENT SIGNALS (چکیده)
58 - Selective Acidic Leaching of Spent Zinc- Carbon Batteries Followed by Zinc Electrowinning (چکیده)
59 - Statistical analysis of thermal conductivity of nanofluid containingdecorated multi-walled carbon nanotubes with TiO (چکیده)
60 - Effects of Fe additions on self propagating high temperature synthesis characteristics of TiO2–Al–C system (چکیده)
61 - Use of grey relational analysis for multi-objective optimisation of NiTiCu shape memory alloy produced by powder metallurgy process (چکیده)
62 - A novel method for fabrication of Fe catalyst used for the synthesis of carbon nanotubes (چکیده)
63 - On the Role of Stearic Acid on the Surface properties of Carbon Nanotubes (چکیده)
64 - Investigation of nano-SiO2 impact on mechanical and biocompatibility properties of cyanoacryalate based nanocomposites for dental application (چکیده)
65 - Effects of hot rolling and inter-stage annealing on the microstructure and texture evolution in a partially homogenized AZ91 magnesium alloy (چکیده)
66 - On the microsegregation of Al–Mg alloys by thermal analysis and numerical modeling (چکیده)
67 - Characterization and nanomechanical properties of novel dental implant coatings containing copper decorated-carbon nanotubes (چکیده)
68 - A comprehensive study on the microstructure of high strength low alloy pipeline welds (چکیده)
69 - Investigation on the effect of nitrate ion on the critical pitting temperature of 2205 duplex stainless steel along a mechanistic approach using pencil electrode (چکیده)
70 - An investigation of the tensile and compressive properties of Al6061 and its nanocomposites in as-cast state and in extruded condition (چکیده)
71 - Nondestructive characterization of microstructure and mechanical properties of intercritically annealed dual-phase steel by magnetic Barkhausen noise technique (چکیده)
72 - Investigation of work softening mechanisms and texture in a hot deformed 6061 aluminum alloy at high temperature (چکیده)
73 - Microstructural analysis and mechanical properties of aluminum matrix nanocomposites reinforced with uncoated and Cu-coated alumina particles (چکیده)
74 - Effect of nanodiamond surface functionalization using oleylamine on the scratch behavior of polyacrylic/nanodiamond nanocomposite (چکیده)
75 - Corrosion evaluation of multi-pass welded nickel–aluminum bronze alloy in 3.5% sodium chloride solution: A restorative application of gas tungsten arc welding process (چکیده)
76 - Synthesis and characterization of permalloy-reinforced Al2O3 nanocomposite powders by mechanical alloying (چکیده)
77 - Comparative study of eddy current and Barkhausen noise nondestructive testing methods in microstructural examination of ferrite–martensite dual-phase steel (چکیده)
78 - The effect of Al 2 O 3 and CaO presence on the kinetics of mechanochemical reduction of MoS 2 by Zn (چکیده)
79 - On the kinetics of TiAl3 intermetallic layer formation in the titanium and aluminum diffusion couple (چکیده)
80 - Pitting corrosion of cold rolled solution treated 17-4 PH stainless steel (چکیده)
81 - EIS assessment of critical pitting temperature of 2205 duplex stainless steel in acidified ferric chloride solution (چکیده)
82 - Biomimetic synthesis and mechanical properties of hydroxyapatite/poly (vinyl alcohol) nanocomposites (چکیده)
83 - The Effect of Conformation Method and Sintering Technique on the Densification and Grain Growth of Nanocrystalline 8 mol% Yttria-Stabilized Zirconia (چکیده)
84 - Synthesis and characterisation of dental composite materials reinforced with fluoroapatite–mullite glass–ceramic particles (چکیده)
85 - In situ synthesis and characterization of nano-size hydroxyapatite in poly(vinyl alcohol) matrix (چکیده)
86 - The role of TiO2, ZrO2, BaO and SiO2on the mechanical properties and crystallization behavior offluorapatite–mullite glass–ceramics (چکیده)
87 - In Situ Synthesis of 2-Phenylbenzimidazole as an Hydrogen Sulfide Corrosion Inhibitor of Carbon Steel (چکیده)
88 - Establishing a correlation between interfacial microstructures and corrosion initiation sites in Al/Cu joints by SEM–EDS and AFM–SKPFM (چکیده)
89 - Use of Eddy-Current Method for Determining the Thickness of Induction-Hardened Layer in Cast Iron (چکیده)
90 - Evaluation of process behavior and crystallite specifications of mechano-chemically synthesized WC–Al2O3 nano-compositesEvaluation of process behavior and crystallite specifications of mechano-chemically synthesized WC–Al2O3 nano-composites (چکیده)
91 - Direct solid state synthesis ofW–Al2O3 nanostructured composite using ammonium paratungstate (APT) and Al powder mixture (چکیده)
92 - Investigation of microstructure and mechanical properties of Al6061-nanocomposite fabricated by stir casting (چکیده)
93 - Electrochemical and quantum chemical assessment of two organic compounds from pyridine derivatives as corrosion inhibitors for mild steel in HCl solution under stagnant condition and hydrodynamic flow (چکیده)
94 - A new equation proposed for evaluation of IR drop on buried pipelines (چکیده)
95 - Creep Characterization of Ni-Based Superalloy IN-792 Using the 4 and 6-h Projection Method (چکیده)
96 - Nanocomposite Catalysts Obtaining by Mechanochemical Technique for Synthesizing Carbon Nanotubes (چکیده)
97 - Influence of Strain Rate on the Toughening Effect of CaCO3 in Polypropylene/CaCO3 Composites (چکیده)
98 - Investigation of microstructural and mechanical properties of austempered steel bar-reinforced ductile cast iron composite (چکیده)
99 - Synthesis of nanostructured AlN by solid state reaction of Al and diaminomaleonitrile (چکیده)
100 - Determination of presence of undesirable carbides at surface of cast iron parts using differential eddy current technique (چکیده)
101 - Microstructure and mechanical properties of extruded Al/Al2O3 composites fabricated by stir-casting process (چکیده)
102 - Shear bond strength and antibacterial effects of orthodontic composite containing TiO2 nanoparticles (چکیده)
103 - Inhibitive assessment of 1-(7-methyl-5-morpholin-4-ylthiazolo[4,5-d]pyrimidin-2-yl)-hydrazine as a corrosion inhibitor for mild steel in sulfuric acid solution (چکیده)
104 - Effect of Heat Treatment of Nanodiamonds on the Scratch Behavior of Polyacrylic/Nanodiamond Nanocomposite Clear Coats (چکیده)
105 - Multi-stage thermomechanical behavior of AISI410 martensitic steel (چکیده)
106 - The Effect of Base Metal Conditions on the Final Microstructure and Hardness of 2024 Aluminum Alloy Friction-Stir Welds (چکیده)
107 - New High-Resolution Solution for Measuring Degree of Sensitization of Duplex Stainless Steel 2205 Using Double-Loop Electrochemical Potentiodynamic Reactivation Technique (چکیده)
108 - In situ inhibitor synthesis from admixture of benzaldehyde and benzene-1,2-diamine along with FeCl3 catalyst as a new corrosion inhibitor for mild steel in 0.5 M sulphuric acid (چکیده)
109 - Comparative study on corrosion behaviour of Nitinol and stainless steel orthodontic wires in simulated saliva solution in presence of fluoride ions (چکیده)
110 - Synthesis of nano-structure molybdenum disilicide from primary mixture of MoO3 + Si + Al through mechanochemical reactions (چکیده)
111 - Eddy current nondestructive evaluation of dual phase steel (چکیده)
112 - Dual-Frequency Approach to Assess Surface Hardened Layer Using NDE Technology (چکیده)
113 - Intelligent modeling using fuzzy rule-based technique for evaluating wood carbonization process parameters (چکیده)
114 - Improvement of Quench Factor Analysis in Phase and Hardness Prediction of a Quenched Steel (چکیده)
115 - Morphology evolution of y- precipitates in GTD-111 Ni-based superalloy with heat treatment parameters (چکیده)
116 - A comparative study on the effect of type of reinforcement on the scratch behavior of a polyacrylic-based nanocomposite coating (چکیده)
117 - The change in the chemical composition and toughness of API 5L-X70 welds by addition of titanium (چکیده)
118 - Effects of alloying elements and microstructure on the susceptibility of the welded HSLA steel to hydrogen-induced cracking and sulfide stress cracking (چکیده)
119 - Effect of titanium addition on the microstructure and inclusion formation in submerged arc welded HSLA pipeline steel (چکیده)
120 - Influences of titanium and manganese on high strength low alloy SAW weld metal properties (چکیده)
121 - Mechanochemical synthesis of tungsten carbide nano particles by using WO3/Zn/C powder mixture (چکیده)
122 - A Study on the Role of Ethylene Glycol/Alcohol Ratio on Synthesis of Nano-Size SnO2 (چکیده)
123 - Controlled Forging of a Nb Containing Microalloyed Steel for Automotive Applications (چکیده)
124 - Impact toughness and microstructure of continuous medium carbon steel-bar reinforced cast iron composite (چکیده)
125 - Air-exposed combustion synthesis of Al2O3 nanofibers in Al/TiO2/C system (چکیده)
126 - Role of fuel/oxidizer ratio on the synthesis conditions of Cu–Al2O3 nanocomposite prepared through solution combustion synthesis (چکیده)
127 - An optimization analysis on electroless deposition of Al2O3/Cu core-shell nanostructures (چکیده)
128 - Fabrication of FeNi–Al2O3 nanocomposites and optimization of mechanical properties using Taguchi method (چکیده)
129 - Magnetic nondestructive technology for detection of tempered martensite embrittlement (چکیده)
130 - Conversion of W2C to WC phase during mechano-chemical synthesis of nano-size WC–Al2O3 powder using WO3–2Al–(1+x)C mixtures (چکیده)
131 - FEM modeling of the flow curves and failure modes of dual phase steels with different martensite volume fractions using actual microstructure as the representative volume (چکیده)
132 - Microstructural and mechanical characteristics of Al-alloyed ductile iron upon casting and annealing (چکیده)
133 - The effect of isothermal heat treatment time on the microstructure and properties of 2.11% Al austempered ductile iron (چکیده)
134 - Tribological properties of multilayer nanostructure TiO2 thin film doped by SiO2 (چکیده)
135 - Carburising behaviour of low carbon steel with nanocrystalline surface layer induced by ball milling (چکیده)
136 - On the Relationship of Magnetic Response toMicrostructure in Cast Iron and Steel Parts (چکیده)
137 - Influence of heat treatment on microstructure and passivity of Cu–30Zn–1Sn alloy in buffer solution containing chloride ions (چکیده)
138 - Dynamic recrystallization and precipitation in low carbon low alloy steel 26NiCrMoV 14-5 (چکیده)
139 - Modeling the electroless nickel deposition on aluminum nanoparticles (چکیده)
140 - Hot deformation and processing maps of K310 cold work tool steel (چکیده)
141 - A comparative study of critical pitting temperature (CPT) of stainless steels by electrochemical impedance spectroscopy (EIS), potentiodynamic and potentiostatic techniques (چکیده)
142 - Fabrication of Fe/Al2O3 composite foam via combination of combustion synthesis and spark plasma sintering techniques (چکیده)
143 - Formation of nanocrystalline h-AlN during mechanochemical decomposition of melamine in the presence of metallic aluminum (چکیده)
144 - Simulation of induction tempering process of carbon steel using finite element method (چکیده)
145 - Prediction of mechanical properties of a warm compacted molybdenum prealloy using artificial neural network and adaptive neuro-fuzzy models (چکیده)
146 - Welding of aluminum alloys through thermite like reactions in Al–CuO–Ni system (چکیده)
147 - The Microstructure and Mechanical Properties of Hot Forged Vanadium Microalloyed Steel (چکیده)
148 - Pain reduction after initial archwire placement in orthodontic patients: A randomized clinical trial (چکیده)
149 - An investigation on the coarsening behavior of γ′ precipitate in GTD-111 Ni-base superalloy (چکیده)
150 - Establishing a New Solution Based on Hydrochloric Acid/Sodium Thiosulfate for Detecting and Measuring Degree of Sensitization of Stainless Steels Using Double-Loop Electrochemical Potentiodynamic Reactivation Method (چکیده)
151 - Effect of aluminum on stability of retained austenite in bainitic ductile cast iron (چکیده)
152 - Improving pore morphology of PM 316L stainless steels by prealloyed powder prepassivation in 20% nitric acid (چکیده)
153 - Effects of lubricant and temperature on friction coefficient during hot forging of Nimonic 115 superalloy (چکیده)
154 - Microstructure evolution in hypereutectoid graphitic steel (چکیده)
155 - Preyssler Heteropolyacid Supported on Nano-SiO2: A Green and Reusable Catalyst in Selective Oxidation of Benzyl Alcohols to Benzaldehydes (چکیده)
156 - Fabrication of A356 composite reinforced with micro and nano Al2O3 particles by a developed compocasting method and study of its properties (چکیده)
157 - A novel electrochemical approach on the effect of alloying elements on self-discharge and discharge delivered current density of Pb–Ca–Ag lead-acid battery plates (چکیده)
158 - A Study on Graphitization Acceleration during Annealing of Martensitic Hypereutectoid Steel (چکیده)
159 - Modeling of mechanical behavior of ultra fine grained aluminum produced by multiple compressions in a channel die (چکیده)
160 - Microstructure and Mechanical Properties of Al–Al2O3 Micro and Nano Composites fabricated by Stir casting (چکیده)
161 - Comparison of microstructure and mechanical properties of A356 aluminum alloy/Al2O3 Composites fabricated by stir and compo-casting processes (چکیده)
162 - Dynamic recrystallization behavior of a superaustenitic stainless steel containing 16%Cr and 25%Ni (چکیده)
163 - Comparing thermal and mechanochemical decomposition of ammonium paratungstate (APT) (چکیده)
164 - Theoretical and electrochemical assessment of inhibitive behavior of some thiophenol derivatives on mild steel in HCl (چکیده)
165 - Formation of metal matrix composite reinforced withNano sized Al2O3 + Ni-Al intermetallics during coating of Al substrate via Combustion synthesis (چکیده)
166 - Effect of Mechanical Milling on the Thermal Behavior of Polyethylene Reinforcedwith Nano-sized Alumina (چکیده)
167 - Study of mechanical deformation of Zr55Cu30Al10Ni5 bulk metallic glass through instrumented indentation (چکیده)
168 - Modeling of microstructure and mechanical behavior of ultra fine grained aluminum produced by accumulative roll-bonding (چکیده)
169 - Microstructural and mechanical properties of friction stir welded Cu–30Zn brass alloy at various feed speeds: Influence of stir bands (چکیده)
170 - The New Methods of Graphite Nodules Detection in Ductile Cast Iron (چکیده)
171 - Investigation of Variables Affecting Impedance Plane in Eddy Current Testing of Carburized Steels (چکیده)
172 - Magnetic NDT Technology for characterization of decarburizing depth (چکیده)
173 - One-step fabrication of Cu–Al2O3 nanocomposite via solution combustion synthesis route (چکیده)
174 - Calculation of forming limit diagrams using Hill's 1993 yield criterion (چکیده)
175 - Hardness profile plotting using multi-frequency multi-output sensor (چکیده)
176 - Critical pitting temperature dependence of 2205 duplex stainless steel on dichromate ion concentration in chloride medium (چکیده)
177 - Microstructural study in graphitised hypereutectoid cast and commercial steels (چکیده)
178 - Inhibitive effect of synthesized 2-(3-pyridyl)-3,4-dihydro-4-quinazolinone as a corrosion inhibitor for mild steel in hydrochloric acid (چکیده)
179 - Effect of electrolysis condition of zinc powder production on zinc–silver oxide battery operation (چکیده)
180 - Correlation between critical pitting temperature and degree of sensitisationon alloy 2205 duplex stainless steel (چکیده)
181 - THE MECHANISM OF LACY COVER FORMATION IN PITTING (چکیده)
182 - Galvanic corrosion of gas tungsten arc repair welds in 17-4 PH stainless steel in 3/5% NaCl solutionr (چکیده)
183 - Post-weld heat treatment influence on galvanic corrosion of GTAW of 17-4PH stainless steel in 3/5%NaCl (چکیده)
184 - manufacturing of aluminum foam sandwich panels:comparison of a novel method with two different conventional methods (چکیده)
185 - Critical pitting temperature (CPT) assessment of 2205 duplex stainless stell in 0.1 M NaCl at various molybdate concentrationsl (چکیده)
186 - Improving the corrosion behaviour of powder metallurgical 316L alloy by prepassivation in 20% nitric acid (چکیده)
187 - Tuning DOS measuring parameters based on double-loop EPR in H2SO4 containing KSCN by Taguchi method (چکیده)
188 - Synthesis of alumina reinforced nanostructured -brass by mechanochemical (چکیده)
189 - On the Dependence of Avrami Indexes of MDPE on Milling Time (چکیده)
190 - Role of Surface Active Agent on Dimensional Stability of HDPE/CaCO3 Nanocomposites (چکیده)
191 - Role of Nano-Size SiO2 Additive on the Thermal Behavior of Cyanoacrylate Nanocomposite (چکیده)
192 - The effect of aluminium content on morphology, size, volume fraction, and number of graphite nodules in ductile cast iron (چکیده)
193 - Production of carbon nanotubes using mechanical milling in the presence of an exothermic reaction (چکیده)
194 - Incorporating Aspect Ratio in a New Modeling Approach for Strengthening of MMCs and its Extension from Micro to Nano Scale (چکیده)
195 - Role of nano-size TiO2 particles on the crystallite size of microwave—Combustion synthesized Al2O3/TiC composite (چکیده)
196 - Effects of Multiwall Carbon Nanotubes on the Thermal and Mechanical Properties of Medium Density Polyethylene Matrix Nanocomposites Produced by a Mechanical Milling Method (چکیده)
197 - Evolution of manufacturing parameters in Al/Ni3Al composite powder formation using blending and mechanical milling processes (چکیده)
198 - Microstructural and mechanical properties (hardness) investigations of Al-alloyed ductile cast iron (چکیده)
199 - An investigation on the variations occurring during Ni3Al powder formation by mechanical alloying technique (چکیده)
200 - Study of the Morphology and Granulometry ofPolyethylene–Clay Nanocomposite Powders (چکیده)
201 - The Influence of Different Heat treatment Cycles on Controlled Surface Graphitization in CK45 Steel (چکیده)
202 - Investigation on the effects of hot forging parameters on the austenite grain size of vanadium microalloyed forging steel-30MSV6 (چکیده)
203 - Study of microstructure and mechanical properties of high performance Ni-base superalloy GTD-111 (چکیده)
204 - A high temperature deformation mechanism map for the high performance Ni-base superalloy GTD-111 (چکیده)
205 - Influence of Nano-Size Al2O3 Weight Percent on the Microstructure and Mechanical Properties of Al-Matrix Nanocomposite (چکیده)
206 - Influence of Hot Deformation Strain Rate on the Mechanical Properties and Microstructure of K310 Cold Work Tool Steel (چکیده)
207 - An assessment of the process of Self-propagating High-Temperature Synthesisfor the fabrication of porous copper composite (چکیده)
208 - Coating of Al substrate by metallic Ni through mechanical alloying (چکیده)
209 - Development and verification of a mathematical model for variations of the specific surface area of mineral powders during intensive grinding (چکیده)
210 - Optimizing the ignition behavior of microwave-combustion synthesizedAl2O3/TiC composite using Taguchi robust design method (چکیده)
211 - Development of a mathematical expression for the variation of amorphization phenomenon during intensive milling of minerals (چکیده)
212 - Control of carbon loss during synthesis of WC powder through ball milling of WO3-C-2Al mixture (چکیده)
213 - The effect of aluminothermic reaction on the progress of carbothermic reaction in simultaneous mechanochemical reduction of CuO and ZnO (چکیده)
214 - Effect of alkaline electrolysis conditions on current efficiency, and morphology of zinc powder (چکیده)
215 - Effect of the aluminum content on the behavior of mechanochemical reactions in theWO3–C–Al system (چکیده)
216 - On the role of nano-size SiC on lattice strain and grain size of Al/SiC nanocomposite (چکیده)
217 - Application of eddy current nondestructive method for determination of surface carbon content in carburized steels (چکیده)
218 - A study on the effect of synthesis parameters on the size of nickel particles in sol–gel derived Ni–SiO2–Al2O3 nanocomposites (چکیده)
219 - On role of stearic acid on morphology ofA-Sic composite powders produced bymechanical aloying methodl (چکیده)
220 - Influence of Austenitising Conditions and Aluminium Content on Microstructure and Properties of (چکیده)
221 - The Influence of Annealing Temperature on the Graphitisation of CK 45 Steel (چکیده)
222 - Effect of chromium content on the microstructure and mechanical (چکیده)
223 - A stochastic model for austenite phase formation (چکیده)
224 - Effect of copper content on the microstructure and mechanical properties of multipass MMA, low alloy steel weld metal deposits (چکیده)
225 - Effect of Martensite Plasticity on the Deformation Behavior of a Low-Carbon Dual-Phase Steel (چکیده)
226 - Thermodynamical computations for Removal of alkali halides and lead oxide from electric arc furnace dust (چکیده)
227 - Copper Leaching from Nanoparticles of Chalcopyrite Concentrate (چکیده)
228 - Microstructural Characteristics of Al-alloyed Austempered Ductile Irons (چکیده)
229 - The Bainite Transformation and the Carbide Precipitation of 4.88% Aluminium Austempered Ductile Iron Investigated Using Electron Microscopy (چکیده)
230 - Graphitization in CK 45 Steel (چکیده)
231 - Phase Transformation Study of Aluminium Containing Ductile irons by Dilatometry (چکیده)
232 - Impression creep behavior of lead-free Sn–5Sb solder alloy (چکیده)
233 - Oxidation behaviour of Al-alloyed ductile cast irons at elevated temperature (چکیده)
234 - crystallinity behavior of MDPE-clay nanocomposites fabricated using ball milling method (چکیده)
235 - Fabrication of NiO/SiO2 nanocomposites using sol–gel method and optimization of gelation time using Taguchi robust design method (چکیده)
236 - The effect of nano-sized calcium carbonate on thermodynamic parameters of HDPE (چکیده)
237 - Prediction of nanoparticles’ size-dependent melting temperature using mean coordination number concept (چکیده)
238 - Combustion Wave Stability in Diluted TiO2/Al/C system in Atmospheric Air (چکیده)
239 - The effects of volume percent and aspect ratio of carbon fiber on fracture toughness of reinforced aluminum matrix composites (چکیده)
240 - Prediction of hardness at different points of Jominy specimen using quench factor analysis method (چکیده)
241 - Investigation of the dependences ofthe mechanical characteristics of an alloyed steel on both the strain rate and the microstructure (چکیده)
242 - Simulation of thixoformability of A356 aluminum alloy using finite volume method (چکیده)
243 - ON THE COMBINED EFFECT OF LUBRICATION AND COMPACTION TEMPERATURE ON PROPERTIES OF IRON-BASED P/M PARTS (چکیده)
244 - Effect of heat treatment, lubricant and sintering temperature on dry sliding wear behavior of medium alloyed chromium PM steels (چکیده)
245 - On the strain rate sensitivity of HDPE/CaCO3 nanocomposites (چکیده)
246 - Effects of pre-strain on microstructure of Ni-Ti orthodontic archwires (چکیده)
247 - Filler toughening of plastics. Part 1-The effect of surface interactions on physico-mechanical prope (چکیده)
248 - Modification of fracture toughness of isotactic polypropylene with a combination of EPR and CaCO3 pa (چکیده)
249 - Microstructure evolution of high-performance Ni-base superalloy GTD-111 with heat treatment paramete (چکیده)
250 - Dilatational shear bands in rubber modified isotactic (چکیده)
251 - Fracture behaviour of isotactic polypropylene under static loading condition (چکیده)
252 - EIS examination of mill scale on mild steel with polyester-epoxy powder coating (چکیده)
253 - Modelling of metal flow during hot forging with regard to microstructurol aspects (چکیده)
254 - Hybrid pp-EpR-GF composites. part II: fracture Mechanisms (چکیده)
255 - the influence of glass fider on fracture behavior of isotactic polypropylene (چکیده)
256 - investigation of deformation mechanism in polyproylene/Glass fober Composite (چکیده)
257 - Isothermal transformation of austenite to bainite in high carbon steels (چکیده)
258 - Effect of Both Uncoated and Coated Calcium Carbonate on Fracture Toughness of HDPE/CaCO3 Nanocomposites (چکیده)
259 - Effects of cooling rate on the microstructure and mechanical properties of the Ni-base superalloy UDIMET 500 (چکیده)
260 - Dependency of physical and mechanical properties of mechanical alloyed Al–Al2O3 composite on milling time (چکیده)
261 - Influence of filler particles on deformation and fracture mechanism of isotactic polypropylene (چکیده)
262 - Tensile deformation mechanisms at different temperatures in the Ni-base superalloy GTD-111 (چکیده)
263 - The Relationship Between Pit Chemistry and Pit Geometry Near the Critical Pitting Temperature (چکیده)
264 - Deterioration in critical pitting temperature of 904L stainless steel by addition of sulfate ions (چکیده)
265 - Evolution of current transients and morphology of metastable and stable pitting on stainless steel near the critical pitting temperature (چکیده)
266 - The effects of different additives in electrolyte of AGM batteries on self-discharge (چکیده)
267 - Using pit solution chemistry for evaluation of metastable pitting stability of austenitic stainless steel (چکیده)
268 - Theory Of Hot Crack Formation (چکیده)
